Reach Logo
THE REACH ACS
REACHNET
THE REACH IP CONTROLLER
VIDEO MONITORING
HOSTING
REACH ACS ARCHITECTURE

DOWNLOADS

Reach ACS Data Sheet

IP Controller Data Sheet

Reach Hosted Video
Monitoring Data Sheet

Access Control as a
Managed Service

 

THE REACH IP CONTROLLER

 

 

The primary function of the Reach IP Controller is to provide an interface between the ReachNetTM server and the access control devices at the door. Reach IP Controllers are designed as single-door access control panels that communicate with a hosted central server over the Internet. While on a LAN connected to the internet, the Reach IP  Controller only requires outbound Internet Access. IP Controllers have been designed to control a single door by using card, PIN or biometric readers. In addition, each IP Controller has 8 inputs and 5 outputs, all of which are fully configurable by using ReachNet from any web browser

 

  • Compatible with all card readers using a Wiegand format
  • Storage of all templates, permissions and schedules and events locally; in case of network failure the door still functions and keeps an uninterrupted log of events
  • Regularly communicates with the ReachNet server to update its database of templates, permissions and schedules
  • Stores and reports every event that occurs at the door, creating an audit trail of everyone who attempts to gain access to the door
  • Stores up to: 60,000+ fingerprint templates or 200,000+ cards/PIN codes
  • Stores up to 10,000+ schedules, including holiday schedules
  • Multiple inputs and outputs
  • 8 inputs: 5 supervised analog and digital inputs and 3 unsupervised inputs compatible for REX devices and pressure, flood and temperature sensors
  • 5 configurable outputs, which may include: electric locks, buzzers, lights and alarms to signal conditions at the door, and any other switchable device or appliance
  • All communications between the ReachNet server and Reach IP Controllers are protected by 256-bit AES encryption, approved by NSA for “TOP SECRET” communications

 

Installation:



Installing an IP Controller is intuitive and very similar to any other access control panel, making it perfect for new sites and retrofits. Since there is no server or software to install, on-site installation time and labor expenses are greatly reduced. All IP Controller programming and account setup can be performed remotely using ReachNet. Configuration templates can be created, saved, and assigned in minutes – freeing up the installation team to finish more projects in less time. Since IP Controllers use TCP/IP communications, they can be networked by connecting to the nearest network hub. If using a WiFi bridge, no network cabling is required at all. In addition, there is no on-site server or software to install, reducing labor costs during installation and lowering the total cost of system ownership.

 

 

Technical Specifications:

INPUT POWER:
24VAC, 40VA UL-approved Class 2 transformer
BACKUP POWER:
UL listed 12VDC, 4Ah or 7Ah, sealed acid/lead backup battery (to be supplied by installer)
OUTPUT POWER:
12VDC power for the combined power usage of all attached devices is not to exceed 1.5 Amps.
INPUTS & OUTPUTS:
- 5 supervised inputs
- 3 unsupervised inputs
- 5 Configurable 12VDC Outputs wired to - 5 single pole, double throw, 10A, 12V relays
DEVICE COMMUNICATIONS:
Supports Wiegand, RS232, RS422, and RS485 devices
NETWORK COMMUNICATIONS:
TCP/IP, 256-bit AES encrypted
ENCLOSURE
- Height: 12” (30.48 cm)
- Width: 12” (30.48 cm)
- Depth: 4” (10.16 cm)
- Material: 19-gauge cold-rolled steel
ENVIRONMENTAL
- Operating Temperature: 32°F to 122°F
  (0°C to 50°C)
- Operating Humidity: 0% to 95% relative humidity, non-condensing
CERTIFICATIONS
FCC Part 15, Subpart B – Unintentional
Radiators, UL 294

 

 

 

 

 

 

 


Copyright 2012 Reach Systems, Inc. All Rights Reserved.
4096 Piedmont Ave. Suite 811, Oakland, CA 94611. P 650.644.4166
Home | Company | Solutions | Products | Media | Support | Partners | Contact